Diagnostic Test

CHECK FOR AN ACTIVE DTC B1C2F-PASSENGER AIRBAG INDICATOR STATUS MISMATCH
NOTE:
Ensure the battery is fully charged.
1. Turn the ignition on, then off, and then on again.
2. With the scan tool, read Occupant Restraint Controller (ORC) DTCs.
  Does the scan tool display active: B1C2F-PASSENGER AIRBAG INDICATOR STATUS MISMATCH?
  
  Yes
  - Go To 2
  No
  - Go To 4
CHECK FOR ACTIVE INSTRUMENT CLUSTER DTCs
1. With the scan tool, read Instrument Cluster DTCs.
  Does the scan tool display and active Instrument Cluster DTCs?
  
  Yes
  - Refer to 2.0L & 2.4L - DIAGNOSTIC CODE INDEX for problems related to the Instrument Cluster.
  - Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE - AIRBAG SYSTEM VERIFICATION TEST .
  No
  - Go To 3
CHECK THE ORC AND INSTRUMENT CLUSTER FOR LAMP STATUS
1. With the scan tool view the Instrument Cluster (CCN) Display.
2. Cycle the ignition key and observe the Passenger Airbag Indicator Lamp (PADL) Request status (Set/Not Set) during the Instrument Cluster bulb check.
3. With the scan tool view the ORC Data Display.
4. Select Indicator Lamp Status from Bussed Inputs and select SRS Indicator Lamp request from the Bussed Outputs.
5. Cycle the ignition key and observe the Passenger Airbag Indicator Lamp (PADL) Status (Set/Not Set) during bulb check.
  Did the Data Display information match each other?
  
  Yes
  
  WARNING:
  Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
  
  WARNING:
  If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to follow these instructions may result in possible serious or fatal injury.
  - Replace the ORC in accordance with the service information.
  - Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE - AIRBAG SYSTEM VERIFICATION TEST .
  No
  - Replace the Instrument Cluster in accordance with the service information.
  - Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to STANDARD PROCEDURE - AIRBAG SYSTEM VERIFICATION TEST .
TEST FOR INTERMITTENT CONDITION
1. With the scan tool, record and erase all DTCs from all Airbag modules.
2. If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.
  WARNING:
  Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
3. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
4. Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated terminals.
5. The following additional checks may assist you in identifying a possible intermittent problem.
6. Reconnect any disconnected components and harness connector.
  WARNING:
  Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
7. With the scan tool, monitor active codes as you work through the following steps.
  WARNING:
  Maintain a safe distance from all airbags while performing the following steps. Failure to follow these instructions may result in possible serious or fatal injury.
8. Wiggle the wiring harness and connectors of the related Switch Bank circuit or component.
9. If only stored codes return, continue the test until the problem area has been isolated.
10. In the previous steps you have attempted to recreate the conditions responsible for setting the active DTC in question.
  Does the scan tool display any ACTIVE DTCs?
  
  Yes
  - Perform the appropriate DTC. Refer to OCCUPANT RESTRAINT CONTROLLER (ORC) - DIAGNOSTIC CODE INDEX .
  No
  - No problem found at this time. Erase all codes before returning vehicle to customer.