LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Jeep >> 2016 >> Compass Sport SE, 2.0L Eng VIN A >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Body - Interior & Exterior >> Instrument Panel >> Panel, Instrument >> Installation >> Installation

Panel, Instrument: Installation: Installation

  1. Before proceeding with the following repair procedure, review all warnings and cautions. Refer to INSTRUMENT PANEL, WARNING .
    WARNING:

    Before servicing the steering column the airbag system must be disarmed. Failure to do so may result in accidental deployment of the airbag and possible personal injury. Refer to WARNING .

    Fig 1: Instrument Panel Assembly
    GC0099108Courtesy of CHRYSLER GROUP, LLC
  2. Install the I/P assembly (1) into the vehicle and position onto the support hooks (4) and alignment pins (5).
    Fig 2: Driver Side Support Bolts
    GC0099107Courtesy of CHRYSLER GROUP, LLC
  3. Install the left side support bolts (4) and tighten to 21 N.m (15.5 ft. lbs.).
  4. Install the center support bolt (3) and tighten to 21 N.m (15.5 ft. lbs.).
    Fig 3: Passenger Side Support Bolts
    GC0099097Courtesy of CHRYSLER GROUP, LLC
  5. Install the passenger side support bolts (2) and tighten to 21 N.m (15.5 ft. lbs.).
  6. Install the fence line bolts and tighten to 21 N.m (15.5 ft. lbs.).
    Fig 4: Center Bezel Fastener Locations
    GC0084621Courtesy of CHRYSLER GROUP, LLC
  7. Install the center I/P to HVAC screws (1).
    Fig 5: Harness Connectors
    GC0099106Courtesy of CHRYSLER GROUP, LLC
  8. Connect the wire harness (1) and ground (2) at the A-pillar.
    Fig 6: Main Wire Harness Connectors
    GC0099105Courtesy of CHRYSLER GROUP, LLC
  9. Connect the main wire harness connectors at the driver's side cowl (1 - 3).
  10. Install the steering column. Refer to COLUMN, INSTALLATION .
    Fig 7: Center Wire Harness
    GC0099104Courtesy of CHRYSLER GROUP, LLC
  11. Position the center wire harness (3) and seat the push pin fasteners (2) fully.
    Fig 8: HVAC Wire Harness Connectors
    GC0099103Courtesy of CHRYSLER GROUP, LLC
  12. Connect the HVAC wire harness connectors (1 - 3).
    Fig 9: Antenna Connector
    GC0099096Courtesy of CHRYSLER GROUP, LLC
  13. Connect the radio antenna (2).
  14. Install the passenger side silencer pad.
  15. Install the driver and passenger side end caps and seat fully.
    Fig 10: A-Pillar Wire Harness
    GC0084620Courtesy of CHRYSLER GROUP, LLC
  16. Connect the A-pillar wire harness electrical connector (3).
    Fig 11: Identifying Center Bezel
    GC0098538Courtesy of CHRYSLER GROUP, LLC
  17. Place the center bezel (2) into position and connect the electrical connectors.
  18. Connect the mechanical connections and seat the center bezel fully to the IP (1).
  19. Install the defroster grille and A-pillar trim panels. Refer to GRILLE, DEFROSTER, INSTALLATION .
    Fig 12: Steering Column Reinforcement Panel & Four Screws
    GC0083940Courtesy of CHRYSLER GROUP, LLC
  20. Install the steering column reinforcement (1) and install the screws (2).
  21. Position the steering column opening cover over the opening and seat the clips fully.
  22. Install the cowl trim panels. Refer to PANEL, COWL TRIM, SIDE, INSTALLATION .
  23. Install the shifter assembly. Refer to SHIFTER, TRANSMISSION, INSTALLATION .
  24. Install the center floor console. Refer to CONSOLE, FLOOR, INSTALLATION .
scientia non olet · About LEMON Manuals